PLC Simulator

For instructors

Petruzella PLC textbook companion: free labs, chapter by chapter

Teaching from Petruzella? This page shows which chapters the 12 free beginner labs give practice on, and which chapters have no lab here. Independent: not affiliated with or endorsed by the authors or publishers.

Petruzella, chapter by chapter

Chapter titles are as listed on the publisher's page in November 2026 (labelled “2025 Release”); other editions may differ. The publisher says the text complements instruction on an RSLogix 500 or RSLogix 5000 platform. Its companion lab book is titled for the LogixPro simulator, a separate purchase. This simulator does not run that lab book. See the LogixPro alternative page.

Petruzella chapters and the free labs that practise them
Ch.Chapter titleTopic, in shortFree labs, and what each checks; how to use it
1Programmable Logic Controllers (PLCs): An OverviewWhat a PLC does and where it is used.

Assign lab 1 after the chapter so students run a real program once. It is a single rung, so it only touches the overview.

2PLC Hardware ComponentsThe CPU, power supply, I/O modules and field devices.No lab

No lab. Use the trainer: have students identify modules and trace an input and an output. A browser cannot teach module installation.

3Number Systems and CodesBinary, hexadecimal and the codes PLCs use.No lab

No lab. Use the chapter's own problems. The free labs are about true/false logic, timing and counting, not number codes.

4Fundamentals of LogicAND, OR and NOT thinking.

Good pairing: students fill in the truth-table section of worksheets 2 to 4 before building, then confirm in the lab.

5Basics of PLC ProgrammingContacts, coils and how a program runs.

Lab 1 is the contact-and-coil exercise. The chapter's instruction-set detail for your brand has no lab here.

6Developing Fundamental PLC Wiring Diagrams and Ladder Logic ProgramsTurning a control circuit into a program: stop buttons, start/stop, latching.

Covers the program half of the chapter. Lab 5 is designed to fail so that the latch in labs 6 and 7 is needed. Wiring diagrams stay paper and bench work.

7Programming TimersTimer instructions and timed sequences.

On-delay only. Assign after the on-delay section; off-delay and retentive timers have no lab, so use the chapter's problems and the bench for them.

8Programming CountersCounting events up to a preset.
  • Lab 10. Count to five (CTU)
    • Five BOX_EYE pulses → CARTON_FULL on
    • Four BOX_EYE pulses → CARTON_FULL still off
    • CNT_RESET after a full carton → lamp off, next carton counts from zero
  • Lab 11. Count five boxes and stop (CTU)
    • Tap START → MOTOR on, CARTON_FULL off
    • Five BOX_EYE pulses → CARTON_FULL on, MOTOR off
    • Three BOX_EYE pulses → MOTOR still on, CARTON_FULL off
    • CNT_RESET after full carton → lamp off, conveyor can restart
  • Lab 12. Carton line (mini-project)
    • START → MOTOR off for 0.5 s, then on after the delay
    • STOP while running → MOTOR off and stays off
    • STOP during the 2 s wait → MOTOR never starts
    • Five boxes → CARTON_FULL on, MOTOR off
    • Three boxes → MOTOR still on, CARTON_FULL off
    • CNT_RESET after a full carton → lamp off, START runs again

Count-up only. Labs 10 and 11 build to the carton line in lab 12. No lab for count-down or up/down counters.

9Program Control InstructionsJumps, subroutines and master control.No lab

No lab. Use the textbook problems and the bench.

10Data Manipulation InstructionsMoving and comparing data.No lab

No lab. The free labs are about true/false logic, timing and counting, not data handling.

11Math InstructionsArithmetic in a program.No lab

No lab.

12Sequencer and Shift Register InstructionsStepping through a sequence of outputs.No lab

No lab. Lab 12 is a timed, counted process, but it does not use a sequencer instruction.

13PLC Installation Practices, Editing, and TroubleshootingInstalling, editing a live program and finding faults.
  • Motor lab 2. Remember the trip
    • ESTOP while running → motor off, FAULT_LAMP on
    • ESTOP released → FAULT_LAMP stays on, motor stays off
    • RESET while THERMAL_OL is still active → fault stays on
    • Cause cleared, then RESET → FAULT_LAMP off, motor still off
    • START while the fault is latched → motor stays off
    • After a reset, START runs the motor again
    • RESET while ESTOP is still active → fault stays on

Only the fault-handling side: motor lab 2 has students latch a fault and reset it. Installation and fault-finding on hardware are bench work.

14Process Control, Network Systems, and SCADAAnalog control, communications and supervisory systems.No lab

No lab among the free beginner labs.

15ControlLogix ControllersThe Logix platform and its tag-based programming.No lab

No ControlLogix project here. The Studio 5000 tutorial page explains that software.

The same topics in two other textbooks

The common textbooks share one spine, so one table covers them. Chapter numbers are for Rabiee (Goodheart-Willcox, fifth edition) and Rehg and Sartori (Pearson, second edition), from the publishers' pages. A dash means the topic is not a separate chapter in the list we checked.

Topic by chapter number in three PLC textbooks, with free labs
TopicPetruzellaRabieeRehg and SartoriFree labs here
Overview of PLCs111
Hardware and I/O devices22, 42No lab
Number systems and codes33–No lab
Logic and relay logic diagrams4, 65, 7–
Basic programming563
Timers784
Counters895
Program control911, 128No lab
Data and math instructions10, 1110, 146, 7, 9No lab
Sequencers and shift registers1213, 1510, 11No lab
Troubleshooting1316–No lab
Process control and networks141712, 14No lab

Rehg and Sartori also has chapters on IEC 61131-3 function block diagrams, text languages and sequential function charts. Those are not in the table and have no lab here.

For a week plan built on this order see the course outline; for paper practice, the worksheets. Questions: paul@plcsimulationsoftware.com.

FAQ

Textbook companion questions.

No. This page is an independent mapping. It is not affiliated with or endorsed by the authors or by McGraw Hill, Goodheart-Willcox or Pearson. Chapter titles are listed so you can find the chapter; the descriptions are ours.

Sources

Chapter lists checked in November 2026. Written by Paul.

  1. McGraw Hill, Programmable Logic Controllers (Petruzella), product pageThe 15 chapter titles (the page labels the title a "2025 Release") and the statement that the text complements instruction on an RSLogix 500 or RSLogix 5000 platform.
  2. McGraw Hill, RSLogix PLC Manual (Petruzella), product pageThe companion lab book, listed there under the title "LogixPro PLC Lab Manual for Programmable Logic Controllers".
  3. Goodheart-Willcox, Programmable Logic Controllers: Hardware and Programming (Rabiee), instructor resourcesThe 18 chapter titles of the fifth edition.
  4. Pearson, Programmable Logic Controllers (Rehg and Sartori), product pageChapters 1 to 16 of the second edition (Pearson New International Edition).

This page is an independent learning resource. It is not affiliated with or endorsed by the authors or by McGraw Hill, Goodheart-Willcox or Pearson. Book and publisher names belong to their owners. Allen-Bradley, RSLogix and ControlLogix are names of Rockwell Automation, Inc.; LogixPro is a product of its own maker.